Pipe and Profile Granulator - ToronPR™ PG PP Series
Granulator for Small-Diameter Plastic Pipe and Long Profiles
The pipe granulator reduces long, small-diameter plastic pipe and extruded profiles into regrind ready for reuse or pelletizing. Pipe and profile extruders, window and door producers, and recyclers use it for scrap that is too long and awkward for a standard granulator. The ToronPR™ PG PP pairs a large-diameter rotor with an angled feed chute so long pieces enter and cut progressively. Six models cover output of 300 to 1,500 kg/h.
Standard granulators struggle with long material because pieces jam across a short hopper or must be cut to length by hand. This design accepts long pipe and profile scrap directly, which saves the time and labor of pre-cutting. A large rotor diameter relative to the cutting width lets the knives bite the end of each piece cleanly. A blower and cyclone carry regrind away from the cutting chamber for collection.
The ToronPR™ PG PP suits pipe, tube, and profile scrap from PVC, PE, and PP extrusion lines. Rotor diameters of 500 to 1,000 mm and motor power up to 132 kW give each size the torque long parts demand. Larger pipe and bulky profiles may need a pipe shredder ahead of the granulator. Torontech matches each model to the part length, wall thickness, and throughput a plant handles.
Pipe and Profile Granulator - ToronPR™ PG PP Series Applications

This profile granulator suits operations that generate long, slender plastic scrap.
- Pipe Extrusion Plants: regrinding start-up scrap, off-spec lengths, and trim from small-diameter pipe and tube lines
- Window and Door Profile Production: granulating PVC window, door, and frame profile scrap for in-house reuse
- Profile Extrusion: reducing cable trunking, edge trim, and custom profile scrap from extrusion lines
- Irrigation and Conduit Products: granulating drip line, small irrigation pipe, and electrical conduit offcuts
- Pipe and Profile Recycling: processing collected small-diameter pipe and profile scrap ahead of pelletizing
- Construction Waste Recovery: reducing plastic trim, profiles, and small pipe recovered from job sites

Pipe and Profile Granulator - ToronPR™ PG PP Series Key Features

The granulator combines a long-part feed design with a large rotor built for pipe and profile scrap.
- Long-Part Feeding: the angled feed chute accepts long pipe and profile pieces directly, reducing manual pre-cutting
- Large-Diameter Rotor: rotors of 500 to 1,000 mm give each knife a long cutting path and high momentum
- Heavy-Duty Knife Layout: 10 to 14 rotating knives and 4 fixed knives take deep, clean cuts through pipe walls
- Pneumatic Discharge: a blower and cyclone remove regrind from the chamber and deliver it for collection
- Built for Extrusion Scrap: suited to small-diameter pipe, tube, and profiles from PVC, PE, and PP lines
- Six Capacity Options: models span 300 kg/h through 1,500 kg/h, with motor power up to 132 kW
Theory and Method
Granulating relies on a high-speed scissor cut. A rotor carrying knives spins inside a cutting chamber fitted with fixed bed knives. Each rotor knife sweeps past a fixed knife with a narrow gap, slicing any material caught between them. Repeated cuts break the plastic into small, uniform particles.
Long parts need a different feeding geometry. An angled feed chute guides pipe and profiles into the cutting chamber end-first, so the knives engage only the leading section of each piece. The large rotor diameter gives each knife a long cutting path and high momentum, so it slices through the pipe wall instead of bouncing off it. The rest of the piece slides forward under its own weight and follows into the cut.
Fewer, heavier knives suit this job. With 10 to 14 rotating knives on rotors up to 1,000 mm across, each knife takes a deep, decisive bite rather than nibbling. Once the regrind is small enough, a blower draws it out of the cutting chamber and carries it to a cyclone. The cyclone separates the particles from the airstream and drops them into a bin or bag.
Pipe and Profile Granulator - ToronPR™ PG PP Series Technical Specifications
| Parameter | ToronPR™ PG PP 560 | ToronPR™ PG PP 630 | ToronPR™ PG PP 730 | ToronPR™ PG PP 830 | ToronPR™ PG PP 1000 | ToronPR™ PG PP 1200 |
|---|---|---|---|---|---|---|
| Capacity | 300-400 kg/h | 350-500 kg/h | 500-650 kg/h | 800-900 kg/h | 1,000-1,100 kg/h | 1,300-1,500 kg/h |
| Rotor Diameter | 500 mm | 550 mm | 600 mm | 800 mm | 900 mm | 1,000 mm |
| Rotating Knives | 10 pcs | 10 pcs | 10 pcs | 10 pcs | 14 pcs | 14 pcs |
| Fixed Knives | 4 pcs | 4 pcs | 4 pcs | 4 pcs | 4 pcs | 4 pcs |
| Motor Power | 30-37 kW | 37-45 kW | 45-55 kW | 75-90 kW | 90-110 kW | 110-132 kW |
| Weight | 2,000 kg | 2,500 kg | 3,000 kg | 3,800 kg | 4,500 kg | 6,500 kg |
Parameters are for reference only and may change according to the final configuration.
Common Specifications
| Item | Description |
|---|---|
| Feed Design | Angled feed chute for long pipe and profile pieces |
| Cutting Principle | High-speed rotor knives against fixed bed knives |
| Discharge | Blower and cyclone |
| Suitable Materials | Small-diameter plastic pipe and plastic profiles |