Plastic Film Squeezer
Plastic Film Squeezer - ToronPR™ PFS Series
Film Squeezer and Densifier for Drying Washed Film and Raffia Before Pelletizing
The plastic film squeezer dries wet film and raffia coming off a washing line and turns it into dense, semi-melted granules ready for pelletizing. Film recyclers use it between the washing and pelletizing stages, where thin, wet film is hardest to handle. The ToronPR™ PFS presses the material with an internal screw, squeezing out water while compression heat drives off more moisture. Five models cover throughput of 200 kg/h through 900 kg/h.
Washed film holds a large amount of surface water, and centrifugal dryers leave thin film wetter than rigid flake. Feeding that wet, fluffy film straight into an extruder causes unstable output and steam problems in the melt. The squeezer solves both issues at once, removing water and increasing bulk density in a single step. Its output feeds a downstream extruder far more easily than loose, damp film.
A cutter at the exit die face dices the squeezed material into compact granules. These semi-melted granules flow freely, store well, and feed a pelletizing extruder at a steady rate. The machine suits LDPE film, agricultural film, and PP raffia from post-consumer and post-industrial washing lines. Torontech matches each model to the washing line output and the downstream pelletizing line it will feed.
Plastic Film Squeezer - ToronPR™ PFS Series Applications

This film dewatering machine fits recycling lines that wash thin, flexible material before pelletizing.
- Post-Consumer Film Recycling: drying washed LDPE bags, stretch wrap, and shrink film between a film washing line and a pelletizing line
- Agricultural Film Recycling: drying washed mulch, greenhouse, and silage film that holds heavy moisture after washing
- PP Raffia and Woven Bag Recycling: drying and densifying washed raffia, woven sacks, and FIBC fabric
- Film Washing Line Upgrades: adding a squeezing stage to existing washing lines where centrifugal drying leaves film too wet
- Pelletizing Feed Preparation: converting loose film into dense granules for steady extruder feeding
- Granule Storage and Transport: producing compact, low-moisture granules that store and ship more efficiently than loose film

Plastic Film Squeezer - ToronPR™ PFS Series Key Features
As a plastic densifier, the squeezer combines dewatering, densifying, and granulating in a single machine.
- Screw-Press Dewatering: the internal pressing screw squeezes water out of washed film and raffia mechanically
- Compression Heat Drying: friction and compression heat evaporate moisture the press cannot remove alone
- Densifying in One Step: loose, fluffy film compacts into dense granules with much higher bulk density
- Die-Face Granulating: a cutter at the exit die dices semi-melted material into compact, free-flowing granules
- Easier Extruder Feeding: dense, dry granules feed a pelletizing extruder steadily, supporting stable output
- Built for Thin Film and Raffia: designed for the high-moisture, low-density material that centrifugal dryers struggle to dry
- Five Capacity Options: models span 200 kg/h through 900 kg/h, with motor power up to 200 kW
Theory and Method
Screw compression dewatering removes water mechanically. A rotating screw draws wet film into a barrel and carries it toward a restricted exit. As the space between the screw flights and the barrel narrows, the material compresses and water is forced out. The squeezed water drains away from the barrel, leaving much drier film behind.
Compression also generates heat. Friction between the screw, the barrel, and the tightly packed film raises the material's temperature as it moves forward. That heat evaporates moisture the press cannot squeeze out and softens the film to a semi-molten state. The softened film fuses into a dense mass with far higher bulk density than loose flake.
A rotating cutter at the exit die face completes the process. As the semi-melted material leaves the die, the knives slice it into small granules. These granules are dry, compact, and free flowing, so a downstream extruder can feed them at a steady rate. Stable feeding gives more consistent melt pressure and output during pelletizing.
Plastic Film Squeezer - ToronPR™ PFS Series Technical Specifications
| Parameter | ToronPR™ PFS 250 | ToronPR™ PFS 280 | ToronPR™ PFS 315 | ToronPR™ PFS 350 | ToronPR™ PFS 400 |
|---|---|---|---|---|---|
| Capacity | 200 kg/h | 300 kg/h | 500 kg/h | 600 kg/h | 900 kg/h |
| Motor Power | 75 kW | 90 kW | 110-132 kW | 160 kW | 185-200 kW |
Parameters are for reference only and may change according to the final configuration.
Process Overview
| Item | Description |
|---|---|
| Feed Material | Washed thin film and raffia with high moisture, delivered from an upstream washing line |
| Dewatering Method | Internal pressing screw squeezes and heats the material |
| Output Form | Semi-melted granules diced at the exit die face |
| Downstream Use | Feed material for a pelletizing extruder |
| Line Position | Between the film washing line and the pelletizing line |