Shredder and Granulator Unit - ToronPR™ SGU Series
Combined Shredder and Granulator Unit for Plastic Containers and Lumps
The shredder granulator turns plastic lumps, purgings, and containers into finished regrind in a single compact machine. Molders, recyclers, and compounders use it when material is too large for a granulator alone but a separate shredder and granulator would take too much floor space. The ToronPR™ SGU mounts a low-speed shredder and a high-speed granulator on one frame, with a blower and cyclone to carry regrind away. Two models deliver 300 to 400 kg/h and 400 to 700 kg/h.
The shredder stage breaks bulky parts into coarse pieces, and the granulator stage cuts them down to regrind ready for reuse. Combining both steps removes the conveyor, intermediate storage, and second operator station a two-machine setup needs. A PLC controls the unit, and a hydraulic ram feeds the shredder at an adjustable speed. The result is a two-stage size reduction system for plastic that fits in roughly the footprint of one machine.
The unit targets plastic containers and pure PE or PP lumps, the bulky, thick-walled scrap common in molding and recycling plants. Square shredder knives with four cutting edges rotate for reuse, which lowers blade cost. Operators load whole parts at one end and collect regrind at the cyclone. Torontech matches each model to the material, throughput, and regrind size a plant needs.
Shredder and Granulator Unit - ToronPR™ SGU Series Applications

This plastic granulator serves operations that need to turn bulky rigid scrap into reusable regrind without a full size-reduction line.
- Injection and Blow Molding Plants: converting purgings, start-up lumps, and rejected parts into regrind for direct reuse at the press
- Extrusion Plants: reducing die purgings and solidified lumps that are too large for a standard granulator
- Container Recycling: processing PE and PP drums, crates, and containers into regrind for washing or pelletizing
- Compounding Operations: recovering off-spec lumps and strands from compounding lines for reprocessing
- Plastic Recycling Plants/Plastic Recycling Equipment: providing compact two-stage size reduction for smaller sites or a dedicated rigid stream
- Small-Site Scrap Recovery: handling occasional bulky scrap at plants with limited floor space

Shredder and Granulator Unit - ToronPR™ SGU Series Key Features
The unit combines two size-reduction stages and pneumatic discharge in a compact layout with simple control.
- Shredder and Granulator in One Unit: two cutting stages on a single frame turn bulky parts into regrind in one pass
- Space-Saving Layout: the combined design takes far less floor space than a separate shredder, conveyor, and granulator
- Simple PLC Operation: a PLC controls the unit, keeping start-up and day-to-day operation straightforward
- Hydraulic Ram Feeding: the ram pushes material into the shredder at a speed adjustable for each material
- Four-Edge Square Shredder Knives: each knife rotates to a fresh cutting edge when one wears, extending knife life
- Pneumatic Regrind Discharge: a blower and cyclone carry regrind away from the granulator for clean collection
- Large Feed Openings: feed openings of 1,250 × 1,070 mm and 1,600 × 1,200 mm accept bulky containers and lumps
- Two Capacity Options: models deliver 300 to 400 kg/h and 400 to 700 kg/h
Theory and Method
Two-stage size reduction splits the job between two cutting principles. A granulator cuts efficiently only when pieces fit its chamber, while a shredder handles large parts but leaves coarse output. Putting anindustrial plastic shredder ahead of the granulator lets each machine work in the size range it handles best. The shredder opens bulky parts, and the granulator finishes them into uniform regrind.
The shredder stage uses low-speed shearing. A hydraulic ram pushes material against a slow rotor fitted with square knives, which shear pieces off against fixed counter knives. High torque at low speed cuts thick lumps without overloading the drive. A screen beneath the rotor holds material in the chamber until it is small enough to pass to the next stage.
The granulator stage works on a scissor-cut principle at much higher speed. Rotor knives sweep past fixed bed knives, slicing each piece cleanly, and a finer screen sets the final regrind size. A blower draws the regrind out of the granulator and conveys it to a cyclone, where the particles drop out of the airstream for collection. This pneumatic discharge keeps the cutting chamber clear and delivers regrind straight to a bag or bin.
Shredder and Granulator Unit - ToronPR™ SGU Series Technical Specifications
| Parameter | ToronPR™ SGU 600 | ToronPR™ SGU 800 |
|---|---|---|
| Capacity | 300-400 kg/h | 400-700 kg/h |
| Shredder Motor Power | 22 kW | 45 kW |
| Granulator Motor Power | 18.5 kW | 30 kW |
| Hydraulic Power | 2.2 kW | 3 kW |
| Blower Motor Power | 4 kW | 5.5 kW |
| Shredder Rotor Diameter | 280 mm | 400 mm |
| Granulator Rotor Diameter | 320 mm | 380 mm |
| Shredder Rotor Speed | 75-80 rpm | 75-80 rpm |
| Granulator Rotor Speed | 560 rpm | 560 rpm |
| Shredder Rotary Blades | 30 pcs | 33 pcs |
| Shredder Fixed Blades | 2 pcs | 2 pcs |
| Granulator Rotary Blades | 15 pcs | 21 pcs |
| Granulator Fixed Blades | 2 pcs | 2 pcs |
| Shredder Screen Size | 40 mm | 40 mm |
| Granulator Screen Size | 10-16 mm | 10-16 mm |
| Shredder Chamber Size | 650 × 600 mm | 800 × 800 mm |
| Feed Opening Size | 1,250 × 1,070 mm | 1,600 × 1,200 mm |
| Discharge Opening Size (H × W) | 500 × 550 mm | 500 × 750 mm |
| Dimensions (L × W × H) | 2,500 × 1,750 × 2,400 mm | 2,900 × 2,000 × 2,500 mm |
| Weight | 3,300 kg | 5,000 kg |
Parameters are for reference only and may change according to the final configuration.
Common Specifications and Options
| Item | Description |
|---|---|
| Configuration | Low-speed single shaft shredder and high-speed granulator on one frame |
| Shredder Knife Type | Square knives with four usable cutting edges |
| Rotor Options | Square knives with indexable cutting edges |
| Feeding System | Horizontal hydraulic ram with adjustable speed |
| Discharge System | Blower and cyclone |
| Control System | PLC |
| Suitable Materials | Plastic containers, pure PE or PP plastic lumps |