Moving Hopper Single Shaft Shredder - ToronPR™ SSS MH Series
Moving Hopper Single Shaft Shredder for Film, bulk bags and Chemical Fibers
The moving hopper shredder breaks down plastic film, bulk bags, chemical fibers, textiles, and other soft or bulky waste that standard ram-fed shredders struggle to feed. Recyclers, textile processors, and packaging waste handlers use it as the first size-reduction step for light, stringy, or high-volume material. The ToronPR™ SSS MH combines a hydraulically driven moving hopper, a high-torque rotor, and a reducer mounted directly on the frame. Six models cover throughput of 200 kg/h through 5,000 kg/h.
Soft material tends to bridge, bounce, or wrap rather than flow into the knives. The moving hopper design addresses this by pressing the whole charge toward the rotor, keeping the cutting zone full and the feed steady. A PLC adjusts feed speed for each material and reverses the rotor automatically when material wraps or jams. Square knives with four cutting edges rotate for reuse, which lowers blade cost and shortens maintenance stops.
The shredder also handles plastic containers, wood, sponges, and industrial packaging waste. That range lets one machine serve several soft and mixed waste streams at the same site. Rotor diameters of 420 to 600 mm and feed openings up to 2,700 × 2,200 mm accept large bales and loose loads. Torontech matches each model to the material, throughput, and downstream process it will feed.
Moving Hopper Single Shaft Shredder - ToronPR™ SSS MH Series Applications

This film shredder suits operations where material is light, bulky, or fibrous enough to resist conventional feeding.
- Plastic Film Recycling: pre-shredding agricultural film, stretch wrap, and baled post-consumer film ahead of washing lines
- bulk bag and FIBC Recycling: reducing woven polypropylene bulk bags, including bags with lifting loops and liners
- Textile and Fiber Waste: shredding chemical fibers, spinning waste, and post-industrial textile scrap for recovery
- Industrial Packaging Waste: breaking down mixed packaging, strapping, and wrapping material from factories and distribution centers
- Foam and Sponge Waste: reducing bulky, low-density sponge and foam into compact pieces
- Plastic Containers and Wood: handling rigid containers and wood waste on sites that process several material types

Moving Hopper Single Shaft Shredder - ToronPR™ SSS MH Series Key Features
The series pairs a feeding system built for soft material with the heavy-duty drive of a frame-mounted reducer.
- Moving Hopper Design: hydraulic feeding presses film, fibers, and large-volume material into the rotor without bridging or bounce-back
- Frame-Mounted Gearbox: the gearbox sits on the frame, shielding it from working vibration and delivering more stable torque output
- Automatic Forward and Reverse: the PLC reverses the rotor to unwind wrapped material and clear jams, reducing stoppages
- PLC-Controlled Hydraulic Feeding: feed speed is programmable and adjustable for each material
- Four-Edge Square Knives: each knife rotates to a fresh cutting edge when one wears, extending knife life and simplifying changes
- Two Rotor Designs: choose a detachable knife-holder rotor or an integrated rotor to suit the material
- Wide Material Range: handles film, bulk bags, chemical fibers, textiles, sponges, containers, wood, and packaging waste
- Large Feed Openings: feed openings reach 2,700 × 2,200 mm on the largest models, accepting bales and loose bulk loads
- Six Capacity Options: models span 200 kg/h through 5,000 kg/h
Theory and Method
Single shaft shredding reduces material through low-speed shearing. A horizontal rotor carries rows of knives that pass close to fixed counter knives mounted in the frame. As the rotor turns, each rotating knife traps material against a fixed knife and shears off a piece. The slow, high-torque rotation cuts tough and fibrous material while generating little heat, dust, or noise.
Light and stringy material creates a feeding problem. A conventional ram pushes along a fixed hopper floor, and soft material can bridge above it, spring back, or wrap behind the ram face. The moving hopper uses hydraulic force to press the whole charge toward the rotor instead. This keeps material packed against the knives, so the rotor bites continuously rather than skimming over a loose pile.
Drive stability matters with fibrous material, because wrapping causes sudden torque peaks. This series fixes the reducer to the machine frame, which lets the frame absorb vibration and keeps gear loading more even. When the motor load spikes, the PLC reverses the rotor briefly to unwind the material, then resumes forward cutting. Square knives present four cutting edges, so operators rotate each knife when an edge dulls.
Moving Hopper Single Shaft Shredder - ToronPR™ SSS MH Series Technical Specifications
Models 760 to 1000
| Parameter | ToronPR™ SSS MH 760 | ToronPR™ SSS MH 800 | ToronPR™ SSS MH 1000 |
|---|---|---|---|
| Capacity | 200-300 kg/h | 300-600 kg/h | 500-1,000 kg/h |
| Motor Power | 37 kW | 45 / 55 kW | 55 / 75 kW |
| Hydraulic Power | 3 kW | 4 kW | 5.5 kW |
| Rotor Diameter | 420 mm | 420 mm | 420 mm |
| Rotor Speed | 50-80 rpm | 50-80 rpm | 50-80 rpm |
| Rotary Blades | 30 pcs | 33 pcs | 42 pcs |
| Fixed Blades | 1 pc | 2 pcs | 2 pcs |
| Chamber Size | 760 × 700 mm | 840 × 800 mm | 1,050 × 1,000 mm |
| Feed Opening Size | 1,400 × 1,050 mm | 1,500 × 1,150 mm | 1,600 × 1,500 mm |
| Discharge Opening Size (H × W) | 650 × 760 mm | 800 × 840 mm | 800 × 1,050 mm |
| Hydraulic Cylinder Stroke | 700 mm | 800 mm | 1,000 mm |
| Dimensions (L × W × H) | 3,100 × 2,150 × 2,280 mm | 3,500 × 2,250 × 2,280 mm | 3,760 × 2,450 × 2,280 mm |
| Weight | 3,500 kg | 4,000 kg | 5,500 kg |
Models 1200 to 2000
| Parameter | ToronPR™ SSS MH 1200 | ToronPR™ SSS MH 1500 | ToronPR™ SSS MH 2000 |
|---|---|---|---|
| Capacity | 1,200-2,000 kg/h | 2,000-3,000 kg/h | 3,000-5,000 kg/h |
| Motor Power | 75-110 kW | 110-160 kW | 110 + 110 kW |
| Hydraulic Power | 7.5 kW | 11 kW | 15 kW |
| Rotor Diameter | 550 mm | 550 mm | 600 mm |
| Rotor Speed | 50-80 rpm | 50-80 rpm | / |
| Rotary Blades | 68 pcs | 105 pcs | 135 pcs |
| Fixed Blades | 2 pcs | 3 pcs | 4 pcs |
| Chamber Size | 1,250 × 1,100 mm | 1,500 × 1,100 mm | 2,000 × 1,200 mm |
| Feed Opening Size | 2,000 × 1,600 mm | 2,700 × 1,800 mm | 2,700 × 2,200 mm |
| Discharge Opening Size (H × W) | 900 × 1,250 mm | 930 × 1,500 mm | 1,000 × 2,000 mm |
| Hydraulic Cylinder Stroke | 1,200 mm | 1,500 mm | / |
| Dimensions (L × W × H) | 4,650 × 3,050 × 2,600 mm | 4,850 × 3,400 × 2,600 mm | 5,200 × 4,000 × 3,000 mm |
| Weight | 11,000 kg | 13,000 kg | 16,000 kg |
Motor power values separated by a slash are alternative motor options. Parameters are for reference only and may change according to the final configuration. A hyphen indicates a power range; a plus sign indicates a dual-motor drive.
Common Specifications and Options
| Item | Description |
|---|---|
| Rotor Designs | Detachable (bolted) knife-holder rotor or integrated rotor |
| Rotary Knife Type | Square knives with four usable cutting edges |
| Knife Material | D2 (SKD11) tool steel |
| Knife Hardness | HRC 55 to 60, adjusted according to material |
| Drive Mounting | Reducer fixed on the machine frame |
| Feeding System | Hydraulic moving hopper with PLC-controlled, adjustable speed |
| Control System | PLC with automatic forward and reverse rotor operation |
| Suitable Materials | Plastic film, bulk bags, chemical fibers, waste textiles, sponges, plastic containers, wood, industrial packaging waste |